A faulty garage door opener in Louisville, KY, can disrupt your entire routine and become a major inconvenience. Fixing it requires a few different steps but is simple enough to do on your own. Learn how to reset garage door openers in this helpful guide from the experts at Action Overhead Door Inc.
Four Steps for Resetting Your Garage Door Opener
Modern garage doors include an electric mechanism that hangs from the ceiling and controls the cables and wires that maneuver the door. They typically also come with a remote that triggers the garage door opener when you press a button or a keypad that only works when you enter the right passcode.
You can reset your system through each of these devices. Check out how to go about this below.
1. Rule Out Electrical Damage
Before you can begin resetting this household equipment, prioritize your safety. A manual reset of your system can turn dangerous if faulty electrical components are present. Perform a quick inspection to check for the following issues:
- Broken switches or outlets in your garage
- Flashing warning light on your overhead device
- Tripped circuit breakers
- A door that only partially opens or closes
Contact a qualified technician to inspect and repair these electrical components before moving forward.
2. Locate the Reset Button on Your Overhead Machine
Anyone wondering how to reset garage door openers should look carefully at the overhead device for the home or learn button. These words should appear near an LED indicator light. Once you find the button, hold it for about ten seconds or until the light turns off.
Doing this will reset the opener itself. You’ll have to take additional steps for a keypad reset or remote programming. Completing only this step without pairing your remotes or access pad means these devices won’t be effective at lifting or lowering your door.
3. Pair Your Remote
Press and then quickly release the learn button on the opener and have your remote in hand. When the LED light begins to flash, you can press the button on your remote to trigger the garage door. Using the remote once will likely affect the garage door’s light.
Try hitting it a second time after the light changes. This should cause the door to lift or lower. Repeat this step with any remotes you keep in your vehicle to ensure they work properly.
Bear in mind that this process only works if you act quickly. After hitting the home button, you only have about 30 seconds to reset your remote. Exceeding this time limit will require you to start the process over again.
4. Enter a New Keypad PIN
Do you control your garage door with a convenient keypad outside the house? This code erasure method will come in handy if you need to make changes to your system’s settings.
Just like with programming your remotes, you’ll have to press the opener’s home or learn button but not hold it down. Look for a blinking LED light and then go to your keypad and submit your new, four-digit passcode, followed by the “Enter” button. Experts recommend avoiding common number combinations, such as “1234” or accessible information like:
- Birthdays
- Phone numbers
- House address
Check your owner’s manual for additional information. Some models will automatically accept the new PIN once you enter it. Others may require you to hit the learn button to bookend the process.
Once you reset the PIN, test it multiple times. You may write the digits down to remember them for future use. Store this information in a secure place so you don’t lose it.
When To Reset Your Garage Door Opener
Knowing how to reset a garage door opener will come in handy in a few different scenarios. We recommend going through this process for both security and convenience, especially when the following occurs:
- You forget the code: If you can’t remember the code that unlocks your garage door’s keypad, you should reprogram the system and memorize the new code.
- You lose the remote: Say someone gets their hands on your system’s remote, and you want to prevent the door from opening for them. Connect your opener to a new remote, and you won’t have to worry about the old one posing a problem.
- You want to restrict access: Consider switching your settings when you provide someone with the garage remote or keypad code and no longer want them to have access to your home.
- You move into a new home: You should learn how to reset a garage door opener so you can update the settings when you relocate. This prevents previous owners or unwanted visitors from accessing the space.
- Your house loses power: A power outage can alter how well your home’s electrical equipment functions, including the garage opener. Reprogram yours after a power failure to be safe.
- Home security issues arise: Be cautious of hackers forcing their way into your home by intercepting data. Updating your equipment will give you peace of mind and ensure no one else can enter your garage.
Signs You Need Professional Garage Door Repairs
Resetting the devices that control your garage’s entryway is a fairly easy DIY project. However, you should let an expert address any serious problem with your system. Reach out to a trusted technician when you experience the following issues:
- The door has a broken sensor.
- The door makes strange noises during operation.
- You notice broken cables or springs.
- The equipment won’t work at all.
Contact Action Overhead Door Inc. for Solutions to Any Garage Door Problem
Now that you know how to reset a garage door opener, you can spring into action any time your system malfunctions or refuses to open. For professional repairs, reach out to our experts at Action Overhead Door Inc.
We’ll quickly figure out the root of the problem and resolve it, as well as give you garage door maintenance tips. Give us a call at 502-955-7725 to schedule service in Louisville and the surrounding areas.
